2013 eXmark LZE730KA604

<< Back to 2013 eXmark Zero Turn Riding Mowers

2013 eXmark LZE730KA604

Lazer Z® E-Series: The definition of value.

The E-Series is the perfect choice for professional landscape contractors who want the innovative engineering and\ncommercial-grade quality of a Lazer Z, but in a value package. The E-Series features the same welded, heavy-duty, 1.5" x 3" tubular steel unibody frame found on more expensive Lazer Z models. You can also choose from three rugged Kawasaki® V-Twin engines or a Kohler® Command™ EFI engine matched to 48-, 52- or 60-inch, full-floating, UltraCut™ Series 4 cutting decks. A digital operator diagnostic module simplifies system monitoring and troubleshooting, while the fuel gauge uses ultrasonic waves to provide a more accurate reading. In short, the Lazer Z E-Series strikes a perfect balance of value and performance.

Features

All

Safety plus convenience: Our Rollover Protection System (ROPS) is engineered for more than safety. Its rear-sloping design also diverts branches away from the operator. And it folds easily for transport.

Single-point height adjust: This simple system lets you adjust deck height without resetting rake and level. Set height of cut from 1 to 5.5 inches by simply moving a bolt.

On-board diagnostics: Check vital functions at a glance on the digital screen. An electronic fuel gauge, battery voltage warning, hour meter and OPC safety switch monitoring make troubleshooting easy.

Hydro drive simplified: Our hydro drive system has no hoses to leak and just two, easy-to-change belts. Only simple, annual maintenance is required. It also lowers the center of gravity for improved handling.

2013 eXmark LZE730KA604

Specifications

Engine

Engine
Kohler Command CV740
Drive
Two Exmark-exclusive Parker unitized pump and wheel motor systems with no hoses, 1.7-quart integrated reservoir, spin-on filter and heavy-duty components. 12cc pumps and 14.5-cubic-inch motors.
Speed
Infinitely variable speed selection 0–8.0 mph (12.9 kmph) forward, 0–6.0 mph (9.7 kmph) reverse.
Fuel Capacity
8-gallon (30.3-L) single fuel tank with single fill location.
Electrical System
12-V battery

Chassis

Turning Radius
True zero-turn.
Steering
(& Motion Control) Hydraulically damped twin levers adjust fore and aft. Adjustable dampers (3 positions) to customize drive responsiveness. Levers are also adjustable to 2 height positions.
Caster Tires
13 x 5.0-6/Pneumatic
(Casters) 0.50"-thick, double-yoke, smooth-tread caster wheel assembly with pre-installed bearing cups.
Drive Tires
23 x 10.5-12 Turf Master®

Dimensions

Deck Width
60" (152.4 cm)

General Information

Deck Lift
Standard; foot-controlled deck lift changes cutting height and lifts the deck to maneuver around obstacles, or place in transport position.
Cutting Height
1.5" (3.8 cm) to 4.5" (11.4 cm) in 0.25" (0.64 cm) increments adjustable from operator’s seat.
Blades
3 Blades at 20.50" Length
(Tip Speed)Approximately 18,500 fpm.
0.20"-thick (5.1 mm) alloy steel.
Frame
(Tractor) Unibody • Welded • Heavy-duty 1.5" x 3" Tubular steel
Parking Brake
Lever-actuated disc brake.
Seat
Commercial Grade High Back contoured foam padded with armrests. Adjustment: Fore and aft from Operators’ Position.
Spindle
(Blade) 1.75" (44.5 mm)-diameter splined blade driver.
Drive Wheels
(Release) Allows unit movement without engine running.
Safety Systems
Operator Presence Controls (OPC)
ROPS
2-post foldable ROPS standard with seat belt and latch.
Standard
Engine hourmeter; Cup holder; deck lift
Deck Construction
10-gauge top that is formed and continuously seam welded, 7-gauge side skirt and 7-gauge reinforced spindle mounting locations for improved strength and reduced weight.
Deck
(Style) Full-floating UltraCut Series 4. Side discharge standard, with molded discharge chute and option to bag or mulch.
(System) UltraCut Series 4/5.5" deep deck/Cutting heights from 1"–4.5"/Wide-flange cutter housings with spindle driver/Chain support and transport auto-lock/Single-point, finite height adjustment.
Cutting
(Performance) Side discharge with option to bag or mulch.
Other
(Diagnostics) Operational diagnostics with integral fuel gauge.
Instruments
Operational diagnostics/Integral fuel gauge and hour meter
Warranty
2 Year, Limited Commercial / 4 Years or 500 Hours, Limited Consumer
Model #
LZE730KA604

Power Take-Off (PTO)

Standard PTO
175 ft-lbs
Engagement
(PTO) MagStop Electromagnetic 175 ft-lbs clutch with spot brake

Photos

Request a quote for: 2013 eXmark LZE730KA604

Estimated Time For Purchase:*
If you see this field, leave it blank:
Characters Remaining

While we attempt to ensure display of current and accurate data, this listing may not reflect the most recent transactions or may reflect occasional data entry errors. All inventory listed is subject to availability and prior sale. Please consult dealership personnel for details. Prices are quoted for the US only and may not include dealer preparation, transportation, taxes, or other applicable charges. Photographs may be representative only and may vary somewhat from the actual items offered for sale.